En medlem på 99.se, bollman, råkade ut för tråkigheter när han skulle låsa upp sin telefon med anySIM som en del av processen att uppdatera en upplåst iPhone till 1.1.1 enligt vår guide. Efter upplåsningen saknande han all radiokontakt, dvs GSM, wifi och bluetooth var helt borta. Efter åtta (!) timmars mekande kom han fram till en lösning som fungerade för att få tillbaka allting igen. Han skriver om det i ett inlägg i forumet och här nedan har vi hans beskrivning (på engelska) för hur han till slut löste det. Kanske kan det hjälpa någon annan där ute?

What to do if your iPhone is totally bricked! (no wifi, no phone, no bluetooth, and you’ll get a message telling you that your iPhone needs repairs)

I got this error after trying to upgrade to 1.1.1 and something went wrong and I was left with a totally wiped baseband.

You need a windows PC and the following:

• iTunes (but make sure it’s turned off)
• iBrickr – http://cre.ations.net/creation/ibrickr
• AppTappInstaller.exe – use google
• Revirginizing Tool – http://code.google.com/p/iphone-elite/wiki/RevirginizingTool
• A mac with iNdependence (or the corresponding tools on the PC, although I had problems getting it work).

Get the phone activated with iNdependence and make sure that you have downgraded to 1.0.2 (there are lots of sites telling you how to do that, but for you they all end up with the same error that your phone needs repairs, never mind that though)

Install apptappinstaller and after that install BSD subsystem and a terminal with the help of iBrickr (you might need to install loads of tiems, I had to, sometimes it seems not to ”stick” in the phone, don’t ask me why).

Using iBrickr, upload the content of the virginizer_tools folder to /usr/bin/virginizer_tools (you’ll have to create this folder with iBrickr because iBrickr can’t upload folders)

Using iBrickr, upload ieraser (located in the iBrickr-folder) to the same folder

Disconnect the iPhone from the PC (otherwise you will get errors trying to flash)

Start the terminal on the iPhone and take a deep breath, here we go:

cd /usr/bin/virginizer_tool [Enter]

chmod +x ieraser [Enter]

chmod +x bbupdate [Enter]

cp 401secpack secpack [Enter]

ieraser [Enter]

– – Now it will erase the firmware, this should take about 20 secs, if shorter, it will not have worked – –

then, run the command to flash the firmware:

./bbupdater -f ./ICE03.14.08_G.fls -e ./ICE03.14.08_G.eep

If all goes well, it will end:

…

ProcessDetailUpdated: Sending end-pack.

ProcessDetailUpdated: Checksum OK.

ProcessDetailUpdated: Verify OK

ProcessOutlineUpdated: Process time was 1 min 52 sec.

Resetting target…

pinging the baseband…

issuing +cpwroff…

Done

Now, try to see what the ./bbupdater -v says…

If all is well, it should say:

Resetting target…

pinging the baseband…

issuing +xgendata…

firmware: DEV_ICE_MODEM_03.14.08_G

eep version: EEP_VERSION:207

eep revision: EEP_REVISION:7

bootloader: BOOTLOADER_VERSION:3.9_M3S2

Done

You now have a working baseband again, have a drink, or something. It took me 8 hours to get to this point…

Now, put your phone in restore mode (check with google) and then restore 1.0.2 firmware with iTunes (use google here too, it includes downloading from Apple)

After restoring, your phone will now be back to normal and can be activated and jailbroken with iNdependence or your tool of choice!

Good luck!

Det här inlägget publicerades torsdag 25 oktober 2007 kl. 00:18 i iPhone, Tips & tricks, Upplåsning. Du kan följa kommentarer genom RSS 2.0. Kommentarer är avstängda just nu, men du kan trackbacka från din egen webbplats.